If a clip’s Properties disagree with the timeline, don’t change the project mode just to make the values match. First check whether Shotcut has misinterpreted that source clip; correct only the affected clip property if so. If the source interpretation is right but the project’s intended delivery format is different, adjust Video Mode or Timeline Properties instead. One layer does not convert the other.
Decide which layer is wrong
Use this sequence before changing settings:
- Write down the project target. Note the intended delivery and the current timeline mode. Record the resolution and frame rate shown in the project settings, plus colorspace and dynamic range if applicable. A mismatch with a source clip is not automatically an error: the project may intentionally use a different format.
- Inspect the selected clip. In Properties, compare Aspect ratio, Scan mode, Color range, and Rotation with reliable information about that source. The Shotcut Properties guide describes these as overrides for the selected clip, including corrections for mis-detection. It cautions against changing Color range without a sound reason. If the Video tab shows a Color transfer value, record it too; the HDR workflow guide identifies PQ, ST428, and HLG values as HDR signals.
- Correct only a confirmed source-reading error. If the picture’s aspect ratio or scan type is demonstrably being read incorrectly, change that property on the affected clip and leave unrelated properties alone. This does not set the timeline’s resolution or frame rate, or convert its colorspace or dynamic range.
- Change the project mode only for a project-level target. If the source readings are credible but the intended sequence format differs from the current mode, use Video Mode or Timeline Properties to set the project target. For HDR, the documented setup includes a compatible colorspace and dynamic-range choice; that is separate from a clip’s Color range override.
Record the decision in a comparison sheet
The values below are hypothetical examples, not a report of a software test or a guaranteed display layout. In your own sheet, use the values actually shown in your project and note where each source observation came from.
| Item | Source observation | Clip override | Project format recorded | Decision and reason |
|---|---|---|---|---|
| Interview A | Camera notes say 16:9 progressive; Properties agrees | None | 1920×1080, 25 fps, BT.709 SDR | Keep both: the source reading is consistent and the project target is intentional. |
| Phone B | File notes say 16:9; Properties reads 4:3; progressive agrees | Change aspect ratio to 16:9 only | Same 1920×1080, 25 fps, BT.709 SDR | Correct the one suspected interpretation error; do not change the project for this clip. |
| Separate HDR case | Properties Color transfer reads HLG; source notes agree | None | Current: BT.709 SDR; intended target: BT.2020 HLG | If HLG is the actual sequence target, revise the project mode; if SDR is the target, use an HDR-to-SDR workflow instead. |
This format makes the reason for each change auditable: it distinguishes a source note, a clip-specific adjustment, and the project target without treating them as interchangeable controls.
Know the limits and choose a next step
If you cannot verify a Color range reading, don’t guess. Shotcut’s guide says a Broadcast Limited indication alongside waveform values below 0 or above 100 can be a clue that the video is actually full range; treat that as a reason to investigate, not as a universal correction rule. Color range is not a substitute for selecting a project colorspace or HDR dynamic range.
For HDR, changing the project mode alone does not perform an HDR-to-SDR conversion. The documentation describes converting to BT.709 or, for HLG, using a LUT workflow. It also notes limits: HDR editing needs 10-bit processing for filters, transitions, or blending, and Shotcut cannot combine different HDR formats in one timeline. If the recorded source and target still disagree, verify the source information first; then choose the project mode or a documented conversion path that matches the intended delivery.
Common follow-up questions
Will changing project resolution fix a clip read as 4:3? No. Resolve a confirmed aspect-ratio interpretation error on that clip; change project resolution only if the sequence target requires it.
Can Color range correct an HLG or BT.2020 mismatch? No. Record Color range separately from colorspace and dynamic range; they are different settings with different purposes.
Should I set the project to SDR for an HLG source? Only if SDR is the intended output, and use a conversion workflow. Selecting an SDR project mode is not itself the documented HDR-to-SDR conversion.
Sources and next step
- Audio/Video Properties - Documentation - English - Shotcut Forum
- Editing HDR Source Clips - Documentation - English - Shotcut Forum
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.