Check the source clip for B-frames first, then establish whether a proxy may be hiding that check, confirm the clip’s Properties speed is exactly 1.000x, and only then inspect the Time Remap mapping. Shotcut’s documentation says Time Remap requires clips with no B-frames and is unavailable when a clip’s speed multiplier is other than 1.000x. A proxy can bypass the B-frame check, but the documentation warns that export may then be very slow or produce bad results. Passing one check is not a general compatibility guarantee.
Diagnose in this order
- Select the timeline clip and identify the actual source file. Before adding Time Remap, record the source file’s B-frame status using a method you can apply to the source itself; do not treat the proxy’s apparent status as the source’s status. The documented requirement is that Time Remap can be added only to clips with no B-frames. If you have already tried to add it and Shotcut shows the Convert to Edit-friendly dialog, record that as a conditional prompt and complete the supported conversion route before evaluating the mapping. The prompt is not a compatibility test and is not proof that an existing proxy is safe for export. See the Time Remap documentation.
- Record whether the clip is using a proxy. If you cannot establish the original file’s B-frame status while the proxy is active, check the original separately before relying on the remap. The official warning is specific: a proxy can mask the check, with potentially slow or poor export results.
- Open the selected clip’s Properties and check Speed. The Time Remap filter is restricted to clips at 1.000x; the clip speed control is a separate setting. Shotcut also notes that Speed can adjust Duration, whereas Time Remap may require you to extend duration when slowing footage. See Audio/Video Properties.
- Once those conditions are understood, inspect the remap keyframes and the source frames they select. The filter maps output time to source time: a flat section holds a source frame, a descending section runs backward, and a steeper slope advances through source time faster. Do not redraw a curve just because export is slow until you have checked the source and clip settings.
- Export a short, representative section and inspect the resulting file outside the editing viewer. Check the intended source moments, visible jumps or freezes, and output duration. Compare with the timeline’s intended mapping before approving a full render.
Record a short acceptance check
This hypothetical worksheet uses illustrative observations, not Shotcut test results or guaranteed outcomes. The source details and export behavior must be checked in your own project. Keep the fields separate so a proxy or speed observation does not stand in for a compatibility check.
| Hypothetical clip | Source B-frame status | Proxy status | Properties speed | Mapping intent | Short-export observation and decision |
|---|---|---|---|---|---|
| Interview A, 12 s | Present | Off | 1.000x | Slow down from 00:04 to 00:06 | Hypothetical case: if Time Remap has already been attempted, a Convert to Edit-friendly prompt may appear; record it, complete the supported conversion route, and only then evaluate the curve. |
| Walk-through B, 18 s | Not yet checked on original | On | 1.000x | Freeze briefly, then resume | Proxy alone does not settle source compatibility; verify the original, then export a short section and inspect the resumed frames. |
| Skateboard C, 9 s | Absent, confirmed on source | Off | 1.250x | Reverse near the end | Speed is outside the documented Time Remap requirement; resolve the speed setting before evaluating the remap. |
| Product D, 14 s | Absent, confirmed on source | Off | 1.000x | Reverse for 1 s | Hypothetical short export shows the expected sequence and duration; this supports approval of this section, not a guarantee for other clips. |
Limits and what to do if it fails
A short export is an author-recommended acceptance check, not a documented guarantee that a full export will behave identically. If the original’s B-frame status remains unknown, stop treating the proxy as evidence and establish the source status or use Shotcut’s documented Convert to Edit-friendly route. If Speed is not 1.000x, address that separate setting before troubleshooting keyframes. If the prerequisites are clear but the short render still has wrong frames, freezes, unexpected duration, or unusually slow progress, isolate the affected section and compare its selected source frames with the intended mapping before changing the curve.
Time Remap cannot be disabled, does not support simple keyframes or filter trimming, and cannot be applied to a track or timeline output. Its audio waveform does not show remapped timing. For audio, listen to the exported section rather than inferring its result from the waveform. If the clip needs a simpler forward-only speed change, Shotcut’s documentation also lists separate Speed filters; choose based on the needed operation and applicable restrictions, not as an assumed fix for every remap export issue.
Does a proxy make a B-frame source compatible?
Not as a guarantee. The documentation says a proxy may bypass the B-frame check, but export can be slow or produce bad results. Verify the original source and test the output.
Should I rebuild the keyframe curve when export is slow?
Not first. Check source B-frames, proxy status, and the 1.000x speed requirement before changing the mapping.
Can the audio waveform confirm the remapped sound?
No. Shotcut says the waveform does not reflect Time Remap changes. Listen to the exported section.
Sources and next step
- Time Remap Filter - Documentation - English - Shotcut Forum
- Audio/Video Properties - Documentation - English - Shotcut Forum
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.