When a Shotcut clip needs both a fixed size and starting position and a keyframed move, use two Size, Position & Rotate filter instances: one for base placement and one for motion. The practical advantage is revision control: you can adjust the framing without editing the motion filter’s keyframes. Shotcut’s documentation explicitly describes applying multiple transform filters to one clip for this purpose. Treat the split as an editing method, not a guarantee that every framing change leaves the final composition unchanged.
Decide and build the two stages
Split the work when the clip’s framing is approved independently of its movement, or when you expect the framing may change after the move has been approved. Keep a single instance if the clip only needs static placement, or if one coordinated animation is easier to maintain as a unit.
- Select the timeline clip and add Size, Position & Rotate from Filters > Video. Shotcut’s documentation says this filter can manipulate image or video size and placement, and can use keyframes. The same filter can be added more than once. Read the filter documentation.
- Use the first instance for static size and base position. Name or record its role as Base placement. Set the intended composition before creating motion points.
- Add a second instance and assign it Motion. Create keyframes for the move in this instance, recording each approved point’s timeline time and visible target. Keep notes about the intended opening, middle and ending positions.
- Disable one instance at a time using its checkbox to compare the result with and without that stage. Shotcut documents that deselecting a filter disables it while retaining its changes; removing it is a separate action. See the documented enable/disable behavior and multiple-filter example.
- If you revise base placement, inspect the motion result again at its recorded keyframe times. A separate filter keeps its keyframe edits separate; it does not promise that changing the base transform preserves every approved screen coordinate.
Use a transformation responsibility worksheet
The following values are hypothetical review notes, not Shotcut defaults or a tested result. Record actual project values and frame observations rather than copying these example numbers. The table helps identify which instance to revise and what to recheck.
| Filter instance | Static size | Base position | Animated points | Change scope | Acceptance frame |
|---|---|---|---|---|---|
| Base placement | Hypothetical: 640 × 360 rectangle | Hypothetical: center at x=720, y=400 | None | Revise this instance for framing | Frame 00:00:00:00: subject fits the intended opening composition |
| Motion | Inherits the reviewed base stage; no new size target recorded | Keyframes: 00:00:00:12 at left mark; 00:00:01:06 at center mark; 00:00:02:00 at right mark | Three approved timeline times; target positions are notes, not a predicted path | Revise this instance for the move | Middle keyframe and both endpoints match the approved visual targets |
| Combined review | Compare against the project’s actual output frame | Check for unexpected crop or placement change | Inspect start, middle and end | Recheck both stages after a base edit | All three frames remain acceptable, or the change is explicitly reapproved |
Limits and what to do when it fails
The filter documentation describes size modes, rectangle controls, position handles, keyframes and enabling or removing a filter. It does not specify that a change to one transform mathematically preserves a later transform’s screen-space position, nor does it guarantee a particular interpolation or motion path. Regard the two instances as separate editing responsibilities, not isolated coordinate universes.
If the base looks correct but the combined clip misses a motion target after a framing change, compare the motion instance alone with the combined result at the affected keyframe. Adjust the motion points only if the approved screen-space target has changed; otherwise restore the intended base values and investigate which stage differs. If disabling either filter does not produce the expected comparison, confirm the selected timeline clip and the actual filter instance before changing values. Preserve the editable project and its recorded times so the change can be reversed without rebuilding the animation.
Common questions
Should both instances have keyframes?
Not for this division of work. Keep the base instance static and put the intended animated points in the motion instance. If the base itself must change over time, record that as an additional animation responsibility and review its interaction with the motion stage.
Can I remove a filter to test its effect?
Prefer disabling it for a reversible comparison. The documentation distinguishes disabling a filter, which retains its changes, from removing it with the minus control.
What should I hand off?
Provide the editable Shotcut project, the role assigned to each transform instance, the recorded keyframe times and target observations, and the responsibility worksheet. The receiving editor can then identify the intended revision scope without guessing.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.