If your Krita timelapse ends before viewers can inspect the finished artwork, you can add a hold during export instead of recording the drawing again. In the Recorder Docker’s export options, use Extend End Result to set how long the last frame stays visible. If you also want to show the finished image before the process begins, enable Result Preview and set its hold. Then check the displayed Video Duration and watch the rendered file: these adjustments add viewing time, while the frame-rate relationship determines the pace of the drawing section.
Choose the export change that matches the problem
Use these steps when the recording already contains the drawing process and its final artwork, but the ending feels rushed or you want a finished-image preview at the beginning.
- Open the Recorder Docker’s export options and note the Input FPS, Video FPS, Video Duration, and the number of frames reported in Recording info. Input FPS is how many recorded frames are used per second of output; Video FPS is the video’s playback frame rate. The manual says that doubling Input FPS relative to Video FPS makes the timelapse twice as fast.
- Decide whether the opening should begin with the drawing process or first show a copy of the final frame. Enable Result Preview only for the latter, and choose the preview hold length.
- Set Extend End Result to the ending hold you want. This holds the last frame so viewers can look at the result; it does not change the capture interval or add drawing actions.
- Recheck Video Duration after changing the frame rates or holds. Use the value as an export estimate, then verify the rendered file’s actual duration and opening and ending frames.
The capture interval and export frame rates are different decisions. Capture interval controls how often the Recorder can take snapshots during interval-based recording; the export settings arrange those recorded frames into a video. For this task, leave the capture settings alone unless you are planning a future recording.
Use a timing worksheet before exporting
The following is a hypothetical calculation for a recording with 600 usable frames, Input FPS 20, and Video FPS 10. The process section would be 60 seconds under that frame-rate ratio. The manual documents that duration changes with FPS settings, but does not specify whether or how its displayed duration rounds or accounts for each hold. Treat these totals as planning estimates, not guaranteed Krita output.
| Export choice | Opening preview | Process estimate | End hold | Estimated total | Viewing decision |
|---|---|---|---|---|---|
| A | 0 sec | 60 sec | 2 sec | 62 sec | Starts with the process; short final inspection |
| B | 4 sec | 60 sec | 2 sec | 66 sec | Shows the result first, then the process |
| C | 4 sec | 60 sec | 6 sec | 70 sec | Same process pace; more time to inspect the ending |
Before export, compare your intended total with Krita’s displayed Video Duration. If it differs from the estimate, use the displayed value and the rendered file as the evidence for your decision. Adjust the holds to suit the project, not to meet these example timings.
Limits and what to check if the result is wrong
Extend End Result is documented as a last-frame hold, and Result Preview as a copy of the last frame added at the start and held for a chosen duration. They affect the presentation around the process, not missing strokes or the quality of the underlying snapshots. The manual lists Result Preview as added in Krita 5.0 and Extend End Result as added in 5.1. Check the documentation for the Krita version you use; do not assume either option exists in an earlier version.
After export, open the file and check three things: its actual duration, whether the first visible image is the artwork or the process, and whether the drawing section still plays at an acceptable speed. If the opening or ending hold is absent, verify the selected options and export again; do not infer a particular failure cause from the result alone. If the process is too fast or slow, revisit the Input FPS to Video FPS relationship and the displayed Video Duration rather than changing capture settings for a recording already made.
The Recorder Docker relies on FFmpeg for video rendering and the manual says it cannot be used on Android; its export option is unavailable there. If export is unavailable on your platform, the documented workflow does not provide a Recorder Docker export there. The manual does not establish a guarantee for how every player reports duration or displays the first frame, so inspect the actual file in the player intended for your audience.
Common questions
Does extending the end slow down the drawing?
It adds time holding the final frame. The process pace is governed by the Input FPS and Video FPS relationship, so judge that section separately.
Will Result Preview replay the start of the drawing?
The manual describes a copy of the last frame at the start, held for a chosen duration. It is a finished-image preview, not a replay of the opening drawing steps.
Do I need to change capture interval to get a longer ending?
No. Capture interval controls snapshot capture during interval-based recording. For an existing recording, use the export hold options; changing the interval is relevant to recording choices, not the requested export adjustment.
Sources: Krita Recorder Docker manual; Krita official manual, Recorder Docker export options
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.