If your drawing combines freehand strokes with the Straight Line or Bezier Curve Tool, start with Krita’s Mirror Tools: the manual says they work with any tool that traces strokes, including those tools and Multibrush. Choose Multibrush when you need a mirror line at a rotated angle or its additional parameters. Before committing, compare the tools you actually plan to use in a short, disposable sketch; the worksheet below is a proposed check, not a reported software test.
Choose and check the route
- List the tools required for the artwork: for example, Freehand Brush, Straight Line, and Bezier Curve. Treat this as your project’s coverage requirement, not as a claim that every Krita tool behaves identically.
- If any listed tool must mirror and it traces strokes, enable the applicable horizontal or vertical Mirror Tool. The manual documents those two axis orientations and says the tools can also be used with Multibrush.
- If the intended mirror line must be rotated away from vertical or horizontal, choose Multibrush instead. The manual identifies it as the option for mirroring along a rotated line and notes that it offers more advanced parameters.
- On a temporary layer, make a short freehand mark, a straight line, and a Bezier curve with the chosen setup. Compare whether each appears on the intended opposite side. This is an author-recommended coverage check; the manual does not promise a particular stroke count, spacing, or curve construction method.
- Record the result for each tool before drawing the final piece. If a required tool does not mirror in your check, use a documented route that covers stroke-tracing tools, or evaluate Multibrush for the rotated-axis requirement. Do not infer coverage from a tool’s icon or name.
Coverage worksheet
The entries below are hypothetical observations to show how to make the choice; they are not Krita test results. “Mirrored in check” should be filled from your own sketch, not assumed from the example.
| Required operation | Hypothetical observation | Decision |
|---|---|---|
| Freehand Brush | A short mark appears on both intended sides | Coverage confirmed for this check |
| Straight Line Tool | The test line appears on both sides with Mirror Tools enabled | Mirror Tools fit this requirement |
| Bezier Curve Tool | The test curve appears on both sides with Mirror Tools enabled | Mirror Tools fit this requirement |
| Rotated mirror line | The planned axis is diagonal, not vertical or horizontal | Use Multibrush for the rotated-axis requirement |
| Multibrush stroke | A short stroke is mirrored in the chosen setup | Record only this observed result; do not generalize to other tools |
Limits and next steps
Mirror Tools are limited to vertical or horizontal lines; they are not the choice for a rotated axis. Multibrush has more advanced parameters, but the cited manual excerpt does not enumerate them, so check Krita’s tool options for the specific control you need rather than assuming a setting exists or behaves a certain way. The manual also does not provide a universal guarantee for every drawing tool beyond its stated stroke-tracing scope.
If one operation fails the proposed check, first confirm which tool you used and whether it traces strokes. Then repeat only that operation with the alternative setup on the temporary layer. If the requirement is a rotated line, try Multibrush; if it is a straight or Bezier stroke on a vertical or horizontal axis, check the Mirror Tools route. Keep the test result as a project-specific note.
Common questions
Can Mirror Tools mirror a Bezier curve? The manual explicitly includes the Bezier Curve Tool among tools that trace strokes and can be used with Mirror Tools. Verify your own required curve in the proposed check.
Can I use Multibrush with Mirror Tools? Yes. The manual says Mirror Tools can be used with Multibrush. That statement does not replace checking the exact combination and result required for your drawing.
Where should I place or lock the axis? This guide compares tool coverage and axis orientation, not axis placement or preventing accidental movement. Consult the [Krita Mirror Tools manual](https://docs.krita.org/en/user_manual/mirror_tools.html) for its documented axis controls; detailed axis positioning is a separate workflow question.
Sources
- Krita Manual: Mirror Tools documents stroke-tracing tool coverage and the horizontal and vertical Mirror Tools.
- Krita Manual: Mirror Tools, rotated-line section identifies Multibrush for a rotated mirror line and notes its additional parameters.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.