Move the Krita mirror axis when the subject’s intended symmetry line does not match the canvas center; keep it centered only when those two references coincide. Treat the axis as a geometric guide for the subject, not as a setting that must follow the canvas midpoint. First identify the reference line in your drawing, then compare its position with the canvas center and test the choice before continuing.
Decide and position the axis
For a front-facing character, the reference might run through the midpoint between the eyes, nose, chin, and torso. For an object, use the design’s intended centerline rather than an edge that merely looks convenient. This is a drawing decision: the documentation explains how to move the axis, but it does not determine which line is right for your subject.
Krita’s Mirror Tools copy a stroke across a mirror line. The manual says you can reposition the line by grabbing its handle; the Move to Canvas Center X/Y option places it at the canvas center. Use that option only when the canvas midpoint is also the intended subject reference. See the Krita Mirror Tools manual.
Use this sequence:
- Identify the intended symmetry reference on the sketch. For a vertical mirror line, choose the subject’s vertical centerline; for a horizontal mirror line, choose the intended horizontal reference.
- Record the relevant canvas midpoint and the reference position in the same coordinate system. Calculate the offset as subject reference minus canvas midpoint. A nonzero offset means the two references differ; it does not, by itself, determine whether the composition should be changed.
- If they coincide, use Move to Canvas Center X/Y for the corresponding axis. If they differ and the subject line is intentional, drag the axis handle to that reference instead.
- Make a few temporary test strokes in a clear area or on a suitable working layer. Check whether the reflected marks land where the design calls for them before drawing detailed features.
- Once positioned, use Lock X/Y Line to hide the move icon. If you also want the axis guide out of view and locked, use Hide Mirror X/Y Line. The manual describes the latter as both locking the axis and hiding its line.
Locking or hiding does not correct a misplaced axis. If you notice a mismatch, restore access to the line, reposition it, and repeat the test before resuming.
Acceptance worksheet
Hypothetical example: a 2400-pixel-wide canvas has a midpoint at x=1200. The character sketch’s intended vertical centerline is x=1370, so the offset is 1370 − 1200 = +170 pixels. These figures illustrate a comparison method, not a Krita test or a guarantee about a particular drawing’s output. The manual does not specify stroke-count or pixel-position rules for such a test.
| Axis choice | Hypothetical five-stroke observation | Decision cue |
|---|---|---|
| Canvas center, x=1200 | A test mark placed on the character’s centerline at x=1370 would be reflected around x=1200, so its partner would appear on the opposite side of that axis, not across the character’s chosen centerline. | Reject this placement if the design requires the character’s centerline to divide the paired marks. |
| Subject reference, x=1370 | A test mark offset 40 pixels to the left of the subject line would have its reflected counterpart the same distance to the right, according to the intended mirror relationship. | Keep this placement if the five test strokes fall on the planned counterpart locations. |
For the worksheet, record five simple marks and compare each pair with the sketch’s intended symmetry. The example is hypothetical: the table describes the expected geometric relationship, not an observed software run. Accept the setup only when the axis crosses the chosen subject reference, test marks match the design, and the axis stays put during subsequent drawing.
Limits and what to do next
The Mirror Tool supports mirroring along a perfectly vertical or horizontal line. If the intended symmetry line is rotated, do not try to imitate it by placing the basic Mirror Tool axis off-center: position and angle are different questions. The manual points to the Multibrush Tool for rotated mirroring and other advanced parameters; see the manual’s rotated-line section. This guide concerns axis position, not a full comparison of symmetry tools.
If the test marks are wrong, first check whether you selected the intended horizontal or vertical Mirror Tool and whether the line crosses the subject reference. Then reposition the line and repeat the same small comparison. If the design needs a rotated axis, consult the Multibrush options instead of treating Move to Canvas Center as an angle control.
Quick questions
Should I always center the axis for a centered canvas?
No. Center it when the subject’s intended symmetry reference is also at the canvas midpoint, not merely because the canvas is centered.
Does hiding the line change the mirror position?
No. The manual describes Hide Mirror X/Y Line as hiding the line while locking the axis. It does not relocate the axis.
What if my character is deliberately asymmetrical?
Decide whether the mirror tool still helps with a particular part of the drawing. If mirrored results conflict with the intended design, stop using that mirror setup for those marks and draw them without relying on the unwanted symmetry.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.