The short answer is: choose from the line relationships you need to preserve. Use a Vanishing Point assistant when one family of parallel lines should aim toward one point. Use a 2 Point Perspective assistant, or two Vanishing Point assistants with a vertical Parallel Ruler, when two horizontal direction families converge. Use Parallel Rulers for orthographic or axonometric technical views where selected directions remain parallel. If the lines must curve toward vanishing points, use Curvilinear Perspective instead. These assistants guide drawing; they do not perform a complete 3D measurement or reconstruction.
Make the Decision
- List the important line groups in the object: horizontal or width, vertical or height, and depth. Mark whether each group remains parallel on the page or converges.
- If only one depth direction converges and the other structural directions stay parallel, use a one-point setup consisting of one Vanishing Point assistant plus two crossing perpendicular Parallel Rulers. The Vanishing Point assistant controls the converging direction; the two Parallel Rulers keep the other structural directions parallel, as in Krita's technical-drawing example.
- If two horizontal direction groups converge toward different points, choose the 2 Point Perspective assistant. It combines two vanishing points with a vertical ruler and provides perspective grid planes; the vertical ruler can be disabled when it is not needed. A manual alternative is two Vanishing Point assistants plus one vertical Parallel Ruler.
- If the view is orthographic, oblique, dimetric, or isometric, use Parallel Rulers for the directions that must stay parallel. For curved perspective, choose Curvilinear Perspective only when straight parallel families are expected to bend toward specified vanishing points.
- Turn on
Snap to Assistantsin the freehand brush options only when you want strokes to follow the assistants. First use the assistants as a preview, then make a short test stroke on a representative corner.
The Krita assistant documentation defines the Vanishing Point, Parallel Ruler, 2 Point Perspective, and Curvilinear Perspective roles. The exact line arrangement remains a project decision based on the object and intended view.
Acceptance Worksheet
The following is a hypothetical record for a cabinet, not a software guarantee or a measured result.
| Observation for the cabinet | Recorded assumption | Assistant decision | Corner check |
|---|---|---|---|
| Width edges across the front | Stay horizontal | Horizontal Parallel Ruler | Top and bottom front edges share direction |
| Upright edges | Stay vertical | Vertical Parallel Ruler, or enabled vertical ruler in 2 Point Perspective | Front corner does not lean |
| Receding depth edges | Converge left and right toward two separate points | 2 Point Perspective assistant | The top, shelf, and base depth edges aim consistently |
| Curvature requirement | None; panels are straight | Do not add Curvilinear Perspective | A temporary stroke along each edge remains straight |
To validate the choice, draw one short stroke for each listed group at the cabinet corner. Reject the setup if a line that should remain parallel is forced toward a vanishing point, or if the two depth directions collapse toward one point. This is an author-proposed comparison method, not an official accuracy test.
Limits and Next Steps
A plausible grid does not prove that the scene has been reconstructed in real-world scale. The 2 Point Perspective assistant uses three points, including a center-of-vision point that affects how its grid is displayed; it does not establish physical dimensions for the cabinet. Likewise, a Parallel Ruler preserves a direction but does not decide which object edges belong to that direction.
If the cabinet corner fails the comparison, return to the line-group record rather than adjusting every stroke individually. Check whether the view is actually one-point, two-point, or an orthographic projection. If the edges visibly bow, reconsider Curvilinear Perspective. If only brush behavior differs from the preview, inspect whether Snap to Assistants is enabled; do not treat a snapping issue as evidence that the chosen geometric model is wrong.
Three Quick Questions
Is a one-point setup always simpler than two-point perspective?
Only when the relevant depth edges share one vanishing direction. A front-facing cabinet can still need two horizontal convergence directions if both side planes are visible.
Should I use the 2 Point Perspective assistant every time two side planes appear?
No. Use it when those planes are represented by two converging horizontal direction groups. For a measured-looking technical view with parallel directions, Parallel Rulers may be the better fit.
Does the assistant correct an inaccurate drawing automatically?
No. It supplies preview or snapping guidance. You still choose the points, classify the line groups, and inspect a representative corner.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.