For color inspection that should not appear in the finished video, use the separate Scope - Vectorscope widget documented in Kdenlive’s View menu while previewing the project. The cited documentation does not establish a View-menu CIE Scope widget. It documents CIE Scope as an effect: use it when the scope itself is meant to appear in the rendered picture, and check the compositing conditions before delivery. Placing the effect on a clip does not by itself guarantee an overlay: the documented setup requires a clip below, and that lower clip needs alpha handling if the scope otherwise obscures it.
Decide what the viewer should receive
Start with the delivery, not the scope name. There are three distinct outcomes:
- Internal analysis: You want to inspect color information during editing, but the audience should see only the edited footage. For the documented View-menu example, choose Scope - Vectorscope, which is a separate widget distinct from the effect that writes a vectorscope into the output. The cited materials do not establish a View-menu CIE Scope widget; do not assume that CIE Scope has this entry.
- Scope as teaching content: The audience should see the scope alongside or over the footage. Choose an effect that produces that image and plan to review it in the render. The Vectorscope effect documentation explicitly distinguishes its output from the separate View-menu widget.
- Ordinary final picture: The scope should not appear in the delivered video. Keep the relevant effect off the output path; an open analysis widget is not a substitute for checking which effects are applied to the timeline clips.
Use this sequence for a review clip:
- Write down whether the scope is for the editor or the audience. If it is editor-only, open the desired scope through View and inspect the project preview.
- If the scope must be visible to the audience, apply the corresponding effect to the intended clip and check the timeline preview. Do not assume that a widget will be included in an export.
- If using CIE Scope as an overlay, place the underlying video on the track below the CIE Scope clip. Check whether the lower clip has an alpha channel. Kdenlive’s CIE Scope documentation says that without alpha, the scope obscures the lower clip; it describes using Alpha Shapes in Min mode, with the rectangle adjusted to the scope dimensions, as a way to create the overlay.
- Before delivery, inspect the rendered result or a representative rendered segment. Confirm that an audience-facing scope is present where intended, and that an analysis-only scope is absent. Also check that the lower footage remains visible wherever the CIE Scope should overlay it.
These steps separate the requested picture from the editor’s measurement display. They do not prescribe a particular project-wide effect-management workflow.
A hypothetical acceptance worksheet
Use the table as a proposed handoff check, not as a report of a software test. The observations below are hypothetical and illustrate what to record; they are not guaranteed Kdenlive outcomes.
| Intended delivery | Hypothetical setup and observation | Decision before delivery |
|---|---|---|
| Internal color check | The documented View-menu Scope - Vectorscope widget is open; the timeline preview shows footage; a rendered review segment contains no scope graphic | Accept if the widget is useful in the editing view and is absent from the delivered picture. The cited materials do not establish a View-menu CIE Scope widget. |
| Scope teaching clip | Vectorscope effect is applied to the teaching shot; the render review shows the scope graphic over the shot | Accept if the audience can see the intended scope and the footage remains legible enough for the lesson |
| CIE Scope overlay | CIE Scope clip is above a video clip; the hypothetical preview shows the scope but hides the lower picture; the lower clip is recorded as having no alpha | Do not treat this as a scope-data fault; address the documented alpha/compositing condition, then review again |
| Ordinary final picture | No output scope is intended; a hypothetical render review shows a scope graphic | Investigate the effects on the rendered clip and remove or disable the unintended output effect before approving the picture |
For the CIE row, use the clip’s actual alpha/type information where available. A dark-looking preview or a track’s color is only a clue, not proof of its media type or alpha state. Record the observed preview and render separately: one does not establish what the other contains.
Limits and what to try next
The cited View-menu documentation establishes a separate Scope - Vectorscope widget; it does not establish a View-menu CIE Scope widget. The documented Vectorscope effect writes scope imagery into the output. Do not infer that every scope has identical effect controls: the Vectorscope effect described in the manual has no parameters or keyframes, while CIE Scope has settings such as color system, CIE system, size and intensity. Those controls affect the scope presentation; they do not replace checking whether the scope belongs in the render.
The CIE Scope documentation describes the lower-track and alpha conditions for an overlay, but it does not establish that every project, clip type or compositing arrangement will behave identically. If the lower footage is covered, first verify the track arrangement and the lower clip’s alpha condition against the documented setup. Then make a controlled preview change to the alpha/compositing arrangement and inspect the result. If the purpose is only analysis, avoid this overlay path and use the separate widget instead. If the scope must be delivered but the compositing result remains unsuitable, keep it as a visible effect only if that matches the intended lesson, or revise the shot layout and review another rendered segment. Do not describe an unrendered timeline preview as a verified export.
Three quick questions
Will a View-menu scope appear in the exported video? The documented View-menu Vectorscope is a separate widget while the project is previewed. For an audience-facing scope, use an effect and verify the rendered picture.
Why does CIE Scope cover the footage below it? Kdenlive documents that the CIE Scope effect displays the scope by default. For an overlay, the lower clip must be present, and the documentation describes alpha handling as necessary when that clip would otherwise be obscured.
Is a Vectorscope effect the same as the widget? No. The effect writes the vectorscope into the output; the View-menu version displays it separately. Choose according to whether the audience should receive the scope image.
Sources and next step
- CIE Scope — Kdenlive 26.08 Manual 26.08 documentation
- Vectorscope — Kdenlive 26.08 Manual 26.08 documentation
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.