If you want one color to remain while the rest of a clip turns gray, first confirm whether the clip’s color data is RGB or YUV. Kdenlive documents Color Hold as removing color from all RGB colors except the selected one. Chroma Hold has a YUV color switch, which its manual says to select when the clip has YUV data instead of RGB. Do not choose by effect name alone, or assume the editor automatically converts the clip between those paths.
Decide and apply the effect
Use the media’s actual type information, such as a format or stream description in the media properties, as your evidence. A node or connector color may be a clue, but confirm the type label rather than treating color as proof. If the information does not establish RGB or YUV, mark the data domain as unconfirmed and check the clip’s properties or its documented media metadata before choosing. The manuals describe the effects’ controls; they do not prescribe a particular way to inspect every clip’s metadata.
- Identify the exact clip being graded and establish whether its data is RGB or YUV. Keep any uncertainty visible in your notes; do not infer the domain from how the image looks.
- For confirmed RGB data, choose Color Hold. For confirmed YUV data, choose Chroma Hold and enable
YUV color. If the domain is still unknown, pause rather than selecting a switch by trial and calling that the correct data path. - Set the
Color keyto the color you want to retain. Use the picker or color control, then inspect both the intended subject and nearby colors that should become gray. - Adjust
SimilarityandBlendseparately, one at a time. Record each value and compare the same representative frames. The Kdenlive manuals define their roles, but do not guarantee a particular value for any clip. - Review the result in motion if the clip moves or its lighting changes. Check that the chosen color remains acceptably colored and that unwanted surrounding colors are acceptably gray. Treat those as separate acceptance conditions.
The manuals explain that low Similarity matches narrowly while high Similarity matches broadly, and that Blend changes how much color is preserved. Those settings therefore call for a visual comparison, not a universal recipe. Color Hold’s documented parameters are described for RGB colors; Chroma Hold’s manual documents the YUV switch and the corresponding controls.
Hypothetical acceptance worksheet
The entries below are hypothetical observations for planning a check, not measured results or promises about Kdenlive. Choose comparison frames that include the target color and nearby colors you want desaturated. Record what you actually see after applying the effect.
| Hypothetical clip and evidence | Effect choice to record | Key color, Similarity, Blend | Observation to record | Decision prompt |
|---|---|---|---|---|
| RGB-labeled product clip; a red label is the target, with orange packaging beside it | Color Hold | Red label; note the actual Similarity and Blend values tried | Is the label still colored, and did adjacent orange also remain colored? | If the target or adjacent region is wrong, compare a different key sample or a controlled parameter change; do not relabel the clip’s data domain based on appearance. |
| YUV-labeled street clip; a yellow coat is the target, with warm shop lights nearby | Chroma Hold; YUV color enabled | Yellow coat; note the actual Similarity and Blend values tried | Is the coat retained, and are the lights gray enough for the intended look? | If either condition fails, review the match and blend separately, then inspect another representative frame. |
| Clip with no confirmed RGB/YUV type label; a blue object appears to be the target | No final choice yet | Record the proposed key and leave settings marked unverified | Visual appearance alone cannot confirm the clip’s data domain | Check media type information before selecting an effect or setting the Chroma Hold switch. |
Limits and next steps
Neither effect can distinguish objects by meaning: the match is based on color, so a different object with a similar color may also retain color. A broad match can preserve colors outside the intended subject; a narrow match can fail to cover its variations. A different Blend value may change the visible balance, but the documentation does not promise it will repair a missed hue or restore color information that is absent from the clip.
If the retained color or gray region is unacceptable, first verify the data-domain evidence and the effect selection. Then inspect the chosen key against the unwanted neighboring colors, change one control at a time, and reassess multiple frames. Kdenlive’s Chroma Hold manual cautions that it is less effective and less easy to apply than Chroma Keep. If Chroma Hold remains unsuitable, consult the current Kdenlive documentation for Chroma Keep and decide whether it fits the task; do not assume it has identical controls or outcomes. If the clip’s data type remains uncertain, resolve that uncertainty before treating an effect result as evidence about the correct domain.
Common questions
Should I select `YUV color` because the clip looks like broadcast footage?
No. The manual ties the switch to whether the clip has YUV data. Appearance or presumed production use is not a substitute for type information.
Does increasing `Similarity` mean only more of my subject stays colored?
Not necessarily. The manual describes a broader color match at higher values; other similar colors may also be affected. Inspect surrounding colors rather than assuming the match follows the object boundary.
Is `Blend` a replacement for choosing the right effect?
No. It controls color preservation within the effect. First choose the path supported by the clip’s data-domain evidence, then evaluate the visual result.
Sources and next step
- Color Hold — Kdenlive 26.08 Manual 26.08 documentation
- Chroma Hold — Kdenlive 26.08 Manual 26.08 documentation
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.