Use automatic keyframing only when you want Kdenlive to record supported Transform changes as you adjust a shot during playback. Choose manual keyframes when a pose must land at a particular frame, or when the parameter you need is outside the documented support range. Before leaving the editing pass, check the toolbar’s red dot, turn recording off, and review the resulting keys.
Decide before recording
The fact that a shot came from an AI tool does not give it a separate keyframing mode: this workflow edits the clip’s effect in Kdenlive. The official effects and filters manual says automatic keyframing works with effects that have X, Y, width, height, optional opacity (alpha), and rotation parameters, and includes Rotoscoping. Do not assume every control in a Transform effect is supported; check the fields on the effect you are editing.
- Select the intended timeline clip and confirm its effect stack is the one you mean to change. Effects can be applied at different project levels, so verify the scope.
- Check that the parameter you plan to change matches the supported set and that Add automatic keyframe is available in the Project Monitor toolbar. If it is unavailable, use manual controls for a supported keyframeable parameter instead.
- Choose automatic recording for a broad move you can shape while playing. Prefer manual placement if the move must begin, stop, or change on exact frames. The default Limit automatic keyframes setting restricts recording to every tenth frame. Keep it for a broad adjustment unless you need denser recording; disabling it removes that limit, not the need to review the result.
- Hover over the Project Monitor and click Add automatic keyframe. Confirm the red dot appears, then play and make only the intended position or handle changes. Separate passes can help keep position and rotation adjustments distinct.
- Stop the pass, click the dot to turn recording off, and inspect the keyframe ruler or panel against the intended motion. If working with effect nodes, treat color only as a clue and confirm the displayed node type label.
Record one short pass in an acceptance worksheet
Use this as a review record, not a prediction of what Kdenlive will generate. The frame numbers below are hypothetical observations for one assumed 25 fps shot.
| Check | Hypothetical record | Decision |
|---|---|---|
| Effect fields | The selected Transform shows X/Y and width/height fields. | These match documented supported parameters; do not generalize to every Transform control. |
| Toggle state | Red dot off before frame 118; on during playback; clicked off after stopping at frame 146. | Recording was limited to the intended pass. |
| Interval choice | Limit automatic keyframes stayed enabled for a broad move. | Keep the limit if the resulting motion is sufficiently controlled. |
| Keyframe review | The hypothetical panel lists keys at frames 120, 130, and 140; the intended final pose is frame 145. | This is sample observation only, not guaranteed output. Set or adjust the exact endpoint manually, then verify it. |
The keyframe section of the same manual describes selecting and moving a key, and copying and pasting keys in the effect keyframe panel. Use those controls when your timing needs a deliberate point rather than relying on playback recording.
Limits and the next step if it fails
Automatic recording is not available for every effect: the monitor toolbar will not offer it for effects outside the documented parameter range. If no keys appear, first check that playback was running, the intended effect and clip were selected, the parameter is supported, and the red dot was visible while you adjusted it. Then turn recording off and use the effect’s manual keyframe controls. If extra keys appear, compare their times and values with the motion you intended; revise the pass or place the required points manually. The manual does not promise a particular key count or exact output for a given gesture, so accept the result by inspecting the keys and previewing the shot.
Three quick questions
- Does an AI shot need a special setting? No. This guide concerns Kdenlive’s clip effect, not the model that produced the shot.
- Can I record position and rotation separately? Yes. The manual describes making automatic-keyframe passes for different adjustments.
- Should I disable the ten-frame limit for an exact endpoint? Not as a substitute for precise placement. Use manual keyframe controls for a frame-specific pose.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.