For a variable-frame-rate (VFR) clip in Shotcut’s Convert to Edit-friendly dialog, leave Override frame rate unchecked unless you have a specific reason to choose another rate: Shotcut says it will use the frame rate set in Settings > Video Mode for detected VFR media. Override only when you intentionally want a different conversion rate; then choose how frames should be handled. This conversion decision is not the same as changing the timeline’s output frame rate.
Decide which rate to use
- Select the clip and open its Properties. Use the Convert button to open Convert to Edit-friendly. If verifiable information already establishes that Shotcut identified the clip as VFR, apply the documented VFR rule. Otherwise leave detection unconfirmed; do not infer it from a phone origin or an average-rate label alone. The documentation describes the behavior for clips detected as VFR, but does not specify a detection report or diagnostic procedure in this dialog. If you cannot establish detection, treat the automatic VFR rule as unconfirmed.
- Read the project’s current rate under Settings > Video Mode. If the clip is detected as VFR and the intended edit rate is the project rate, leave Override frame rate unchecked. Shotcut’s documentation says that, in this state, a detected VFR clip is automatically assigned the Video Mode rate for the converted file.
- If you need a specific conversion rate different from that automatic choice, check Override frame rate and enter the rate you intend to use. The frame-rate conversion method becomes selectable only when this override is on.
- Choose the method based on the motion trade-off: Duplicate skips or repeats frames and is described as fast; Blend combines adjacent frames to make frames as needed; Motion Compensation uses an algorithm to generate frames and is described as slow. These are alternatives for an overridden conversion, not extra settings to choose on the automatic route.
- Start the conversion, then inspect the resulting clip’s Properties and compare the converted file with the source at representative motion and audio points. The documentation says the project clip is automatically replaced when the job finishes; it does not promise a particular cadence, image quality, or synchronization outcome for every source.
Hypothetical 30 fps worksheet
The figures below are an example decision record, not a tested result or a promise about Shotcut’s output. Suppose a creator has a project set to 30 fps. Record VFR detection as confirmed only when there is verifiable supporting information; this guide does not prescribe a confirmation method.
| Observation or decision | Hypothetical entry | What to check next |
|---|---|---|
| Source status | VFR detection: confirmed / unconfirmed | Record the basis if confirmed; the cited documentation specifies no confirmation method. If unconfirmed, do not treat the VFR automatic rule as verified |
| Project rate | Settings > Video Mode: 30 fps | Confirm this is the intended editing cadence |
| Override | Off | Expect the documented automatic choice to follow Video Mode for detected VFR |
| Conversion method | Not selected | Method choice applies only if Override frame rate is enabled |
| Converted properties | Inspect the replaced clip’s reported rate and duration | Compare with the intended project rate and source; investigate any unexpected change |
| Motion and sound review | Check a moving subject and a clear audio event | Note visible cadence or synchronization concerns; do not assume conversion fixed them |
Limits and what to do if it fails
The automatic rule is documented for VFR media Shotcut detects. The supplied documentation does not explain how to confirm detection, how it handles a clip that is not identified as VFR, or guarantee that matching the project rate will eliminate playback or synchronization problems. If detection is unclear, or the result does not meet the editing need, make a deliberate override only after establishing the desired rate. Compare the converted clip against the source; if motion or sound is unacceptable, do not treat a successful conversion job as proof of a successful result. Reconsider the conversion rate or method and review the source and project settings. Avoid changing a rate label or project export setting as a substitute: neither is the documented edit-friendly conversion decision described here.
Common questions
Should I always force the project rate? No. For detected VFR, leaving the override off already tells Shotcut to use the Video Mode rate for the conversion. For other media or uncertain detection, the supplied documentation does not define the automatic behavior.
Which method should I choose when overriding? Use Duplicate when speed is the priority and skipping or repeating frames is acceptable. Consider Blend or Motion Compensation when you want generated intermediate frames, weighing blending against the latter method’s documented slower processing. Review the actual result; no method is guaranteed to suit every clip.
Does this set the final export rate? No. This question concerns the rate and frame handling of the edit-friendly converted clip. It does not establish the timeline’s export settings.
Sources: Shotcut Convert to Edit-friendly dialog; Shotcut Audio/Video Properties.
Sources and next step
- Convert to Edit-friendly Dialog - Documentation - English - Shotcut Forum
- Audio/Video Properties - Documentation - English - Shotcut Forum
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.