To create a shared pause in a Krita AI-animation shot, insert a keyframe column from the Frame Timing Header rather than moving keys one layer at a time. The column command adds frames to every layer currently visible in the Animation Timeline Docker, so first decide exactly which layers should participate. Then check the resulting timing on each row; do not assume the edit included layers that were hidden from the docker.
Decide which layers should move, then insert
This approach fits when several animated layers need the same block of time at the same point, such as a character, a separately animated prop, and an effect that should all wait before the next beat. It is not the right choice if only one layer needs retiming.
- Open the Animation Timeline Docker and list the animated layers that should receive the added time. The active layer is shown automatically. To keep another participating layer visible while a different layer is active, pin it using the pushpin beside its name. The manual says the column command adds frames to each layer currently visible in the Timeline Docker; it does not specify that pinning or the canvas visibility toggle independently determines which layers the command affects. Treat the visible-layer scope as documented, then verify the result on a reversible copy.
- Record the insertion point as a frame number, not a time in seconds. For example, write “insert before frame 48.” Krita’s timeline uses frame positions; playback speed depends on the animation frame rate and playback settings.
- Position the pointer over the Frame Timing Header above the frame table, at the intended boundary, and open its context menu. Choose Keyframe Columns > Insert Keyframe Column Left to add columns before that position. The manual describes this command as adding new frames to each layer currently visible in the Timeline Docker.
- Inspect every participating row around the boundary. Compare the keyframe positions, colored hold lines, and empty slots before and after the insertion. Also check the first key or section boundary after the inserted area, since later timing is part of the shot’s structure.
The header menu operates on columns across layers currently visible in the Timeline Docker. By contrast, dragging selected keyframes in the frame table moves the selected frame or frames and can move them across animation layers. Shift-dragging moves the selected frame or frames and all frames to their right; the manual specifies this behavior but does not establish an additional single-layer restriction. These frame-table operations are different from inserting a shared column, so using them repeatedly across rows can leave layers out of sync. See the Animation Timeline Docker manual for the column-menu and frame-table controls.
Use a comparison worksheet to accept the edit
Before changing the shot, note the frame numbers and timing marks on a duplicate timeline or other reversible working copy. The figures below are a hypothetical review example, not a promised result or software test. Suppose the intended insertion is before frame 48, and the desired pause is 6 frames. Record what each row actually shows afterward rather than treating the planned duration as proof of the outcome.
| Visible layer | Before: next key / hold / blank span | After: observed next key / hold / blank span | Decision |
|---|---|---|---|
| Character | Key at 48; hold to 47 | Key at 54; hold crosses the inserted area | Accept if the pause is intended and the next pose begins at the planned beat |
| Prop | Key at 52; empty slots 48–51 | Key at 58; empty span still visible before it | Check whether the prop should hold or remain empty during the pause |
| Effect | Key at 46; hold to 50 | Key positions and hold boundary appear unchanged | Stop and inspect whether this layer was visible when the command ran |
Use the actual keyframe and hold indicators, not color alone, to identify what each row contains. Krita represents a keyframe as a filled or hollow block and shows a held drawing with a colored line; the line is a timing cue, not a separate keyframe. The manual explains these indicators in its keyframe and hold descriptions.
Limits and what to do when rows disagree
The manual describes column insertion as adding frames to each layer currently visible in the Timeline Docker. It separately says that pinning keeps a layer visible there when inactive, but does not state that pinning itself controls the command’s scope. If a row did not change as expected, inspect the timeline on your working copy and compare its keys and holds at the insertion boundary before making further edits. This comparison is an author-recommended check, not a documented guarantee about how every layer configuration is handled.
If the shot needs only one layer to shift, use a layer-specific keyframe operation instead and review that row’s neighboring timing. If the result is unclear, undo the edit on the working copy and repeat with a smaller, clearly recorded insertion point; the documentation does not specify an automatic rule for resolving every combination of keys and holds. After a successful edit, scrub across the boundary and review the transition into the next section. A timeline edit alone does not establish that the finished shot’s visual timing is approved.
Common questions
Does the command include hidden layers? The documented operation applies to layers visible in the Timeline Docker. Check the layer list and pin intended inactive layers before using it.
Should I drag each keyframe instead? Only when the required change is specific to selected keys or a single layer. For a shared time gap, the header’s column command is designed to add frames across the visible rows.
Will a hold line add a separate drawing? No. A hold indicates that a keyframe’s drawing remains in use until the next keyframe on that layer. Check the keyframe block itself when deciding whether a new drawing was created.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.