When an AI-generated animation pose seems to jitter, compare the current drawing with just the neighboring frames under fixed onion-skin settings. If the same anchor moves irregularly across several frames, investigate pose spacing or timing; if one frame alone breaks an otherwise consistent sequence, inspect that drawing for a local error. These are diagnostic clues, not proof: confirm the cause by changing one time position and reviewing the result in playback.
Set a consistent comparison and inspect the anchors
In Krita, use the lightbulb on the animated layer to show onion skins. The Onion Skin Docker controls visibility, master opacity, opacity for individual frame offsets, tint strength, and the colors assigned to previous and next frames. The manual says onion skins are unavailable when the animated layer is fully opaque; if the lightbulb does not produce overlays, check that condition before diagnosing the artwork. See the official Onion Skin Docker manual.
- Go to the frame that appears to jump. In the Docker, enable only the nearest previous and next frame offsets; turn off more distant offsets so they do not complicate the comparison.
- Set the master opacity, the opacity for each enabled offset, tint strength, and previous/next colors. Keep those settings unchanged while inspecting the suspect interval. Choose tints that are distinguishable against the drawing; color is a visual cue, not a substitute for identifying which frame is previous or next.
- Compare four anchors: head center, shoulder line, wrist, and the point where each foot meets the ground. For each, note whether its location and direction change smoothly from previous to current to next. Also check whether the torso and limbs move consistently with those anchors.
- If several anchors show a similar abrupt change across the interval, inspect the timing and poses on both sides before adjusting. If one anchor or limb is anomalous in just one drawing while the surrounding poses agree, inspect that frame as a possible local drawing error.
- Change one time position per revision: adjust a key pose or add a drawing where the sequence indicates it is needed. Keep other positions unchanged, then repeat the same anchor comparison and play the interval. Record whether the suspected jump improved, remained, or shifted elsewhere.
Use a worksheet to make the decision
The following is a hypothetical observation log, not a Krita test or a guaranteed outcome. “Units” are arbitrary screen-space notes chosen by the animator, not a measurement supplied by Krita. They help keep this creator’s comparison consistent; they do not imply that a particular distance is correct.
| Suspect time | Previous → current → next observations | Working diagnosis | One-position change and playback note |
|---|---|---|---|
| 12 | Head: 48 → 62 → 76; wrist: 31 → 45 → 59; feet: steady | Several anchors advance similarly; review timing or spacing across the interval | Move or add a pose at time 12 only; record whether playback feels more even |
| 18 | Head and shoulders align with neighbors; right wrist alone shifts sharply in the current drawing | Possible local wrist error; inspect that drawing before changing timing | Correct the wrist at 18 only; compare the same three frames again |
| 24 | Head, shoulder line, wrist, and both foot contacts all change direction at the current pose | Possible intentional transition or a wrong pose; inspect the pose design before judging spacing | Change the pose at 24 only, then review the transition in context |
A useful acceptance note records the frame, the four anchor observations before the edit, the single change made, the observations afterward, and the playback result. If an edit improves one anchor but creates a new discontinuity in another, do not mark the interval approved yet.
Limits and what to do when the diagnosis fails
Onion skins show neighboring drawings as overlays; they do not determine whether an AI pose is anatomically correct, identify the intended timing, or automatically distinguish a drawing mistake from an intentional fast movement. The manual describes display controls, not a diagnostic rule or a guaranteed repair. A tinted overlap can also make lines harder to judge, so compare anchor positions and line direction rather than color intensity alone.
If you cannot see any overlays, first check that the layer is animated and not fully opaque, then confirm that onion-skin visibility and the relevant offset controls are enabled. If overlays appear but the cause remains unclear, inspect the individual current and neighboring drawings at the same zoom, mark the four anchors, and review playback over a short interval. If changing one position does not resolve the jump or moves the problem, undo that trial and reconsider whether the poses, timing, or intended action need review together. Onion skins cannot restore details absent from a drawing.
Three quick questions
Should I lower opacity until the poses stop overlapping?
Not as the first diagnostic change. Fix the enabled offsets and transparency settings, then keep them constant. Changing opacity between comparisons can change how easy an overlay is to read without changing the underlying pose relationship.
Do different onion-skin colors prove which frame I am seeing?
Use the Docker’s previous- and next-frame controls to assign colors, but verify the offset toggles and the frame you are inspecting. Treat color as a cue, not as proof of frame identity.
When should I add an in-between drawing?
Consider it when the neighboring poses and intended action make the transition clear but the current interval still reads unevenly in comparison and playback. The documentation does not prescribe a correct frame count or spacing; make one considered change and review the result.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.