Select the repaired interval in Krita’s timeline, open File > Render Animation, and verify that First Frame and Last Frame match the intended endpoints before rendering. Krita’s manual states that these fields are automatically taken from the first and last frames of the current timeline selection. This makes the operation a local re-render, not a new export of the entire animation. Afterward, inspect the rendered result together with the frame immediately before and after the repaired interval; a timeline preview alone does not establish that the join is correct.
Decide and operate
Use this workflow when the original animation is acceptable outside a known repaired interval and you need a replacement output for that interval. The exact frame numbers below are an assumed example, not a software test.
- Identify the original range and the repaired range. For example, the surrounding animation may run from frame 0 to 119, while the AI repair affects frames 48 through 62. Write down frame 47 and frame 63 as the boundary checks.
- In the timeline, select the repaired frames from 48 through 62. Confirm visually that the selection begins and ends on the intended frame cells, rather than relying on a nearby playhead position.
- Open File > Render Animation. Under the range controls, compare First Frame with 48 and Last Frame with 62. If either field is different, stop and correct the selection or the field before rendering.
- Choose an image sequence or video destination and give the output a distinct name or number, such as
repair_048_062_v01. Krita documents that video rendering first creates a PNG sequence and then encodes that sequence, so retaining the sequence can help isolate a bad rendered frame when that option is available. - Render the selected interval. The short output contains only frames 48–62; it does not contain frames 47 or 63. Obtain frame 47 and frame 63 from the original, unchanged animation, then place them beside the local output’s frames 48 and 62, or replace only frames 48–62 in a review copy while preserving the original project frame numbers. Do not duplicate frame 47 or 63, and do not omit either neighbor when checking the join. The local output is not a complete replacement for the full animation unless you intentionally assemble it with the surrounding material.
A useful acceptance worksheet
The worksheet below is an author-recommended comparison method. It records evidence around the join; it is not a promise that Krita will produce a particular visual match or frame count.
| Item | Assumed record | Decision rule |
|---|---|---|
| Original interval | 0–119 | Keep as the surrounding reference |
| Selected render | 48–62 | Accept only if First Frame = 48 and Last Frame = 62 |
| Output identifier | repair_048_062_v01 | Increment the identifier for another render |
| Frame before repair | 47: hand enters from the left | Compare against the repaired sequence’s first visible motion |
| First repaired frame | 48: hand is near the same entry position | Reject or investigate if the pose, position, or timing jumps |
| Last repaired frame | 62: hand reaches the approved contact pose | Compare with frame 63, not only with the timeline preview |
| Frame after repair | 63: hand begins the next movement | Accept only when the transition is visually coherent |
| Result | Hypothetical observation: frame 48 matches frame 47’s approach, but frame 63 shows a one-frame pause | Re-render or revise the repaired endpoint; do not approve from the middle alone |
Take frames 47 and 63 from the original, unchanged animation. Review them beside the local render’s frames 48 and 62, or assemble a temporary review copy by replacing only the original frames 48–62 with the rendered frames while retaining the original project frame numbers. Verify that frame 47 remains immediately before 48 and 62 remains immediately before 63; do not append the neighbors to the short output as new replacement frames. This is a boundary-focused check, not a claim that the source and output have identical internal encoding.
Limits and next steps
A selected range does not automatically prove that the AI repair preserved motion continuity, exposure, layer behavior, or audio timing. The official manual defines how the selection supplies the render endpoints; it does not define an automatic seam-quality test. If the wrong frames appear, first compare the timeline selection with the dialog’s two endpoint fields. If the endpoints are correct but the join fails, inspect the repaired content and its neighboring frames, then make a narrower or revised repair and render it under a new output identifier.
For video output, Krita’s manual also notes that FFmpeg or the platform’s encoder participates in the process, depending on the platform. Codec playback problems are therefore separate from a wrong frame range. On Android, the documented export behavior differs and FFmpeg should not be installed for this purpose. A transparent element may render as black in video; add an opaque bottom layer only if that matches the intended result. These are export limitations, not evidence that the selected repair range was correct.
Three quick questions
Does selecting frames replace the full animation? No. It supplies the first and last frame for the render operation. Treat the output as a local interval unless you deliberately combine it with the unchanged surrounding frames.
Where do I get the frames outside the selected render range? Take them from the original, unchanged animation. For a 48–62 render, use original frame 47 and original frame 63 as neighbors, and compare them with rendered frames 48 and 62 or with a temporary review copy that replaces only frames 48–62. The short render itself does not include those outside frames.
Can I approve the result from Krita’s timeline preview? No. Use the rendered material and compare the boundary before and after the repaired range. The preview can show the intended timeline without proving that the exported frames rejoin correctly.
Sources
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.