If you use Kdenlive’s 3-way Rotate and then need to reposition the image, first check whether the rotation has pushed wanted pixels beyond the project frame. The manual warns that this effect crops the clip at the project frame; a Transform placed after it acts on that cropped clip and cannot bring the rotated-out pixels back. Arrange and assess the geometry before that crop where possible, then inspect all four edges. Do not assume Corners and 3-way Rotate can be freely swapped: verify their actual order and result in your timeline.
Diagnose the chain before adjusting it
Treat the effect list as an ordered sequence, not as a collection of independent controls. Kdenlive documents 3-way Rotate as rotating on X, Y, and Z axes, with an offset that can move the image before rotation. Its warning describes the specific loss of pixels beyond the project frame. Read the 3-way Rotate manual.
- Identify the clip and list its active geometry effects in their current order: Corners, 3-way Rotate, and Transform, if present. Record keyframes or animated values that affect the shot.
- For each effect, note whether the image still shows the source edges you need, or whether an edge has disappeared at the project frame. Mark the first step where that happens; this is the first observed crop in your chain, not an inferred pixel count.
- If later repositioning is required, compare a chain with the required positioning or perspective adjustment before 3-way Rotate against the current chain. Make one ordering change at a time and judge the same frames at the same monitor scale.
- Check the highest-rotation moment, the moment the subject is closest to each frame boundary, and the clip’s first and last frames. Inspect left, right, top, and bottom separately.
- Keep Corners as a separately tested node in this comparison. Repeat with the relevant Corners and 3-way Rotate orderings; do not infer that perspective mapping and rotation commute. The supplied manual pages do not define their combined result or every ordering’s render behavior.
The manual describes Transform as a clip transformation and compositing effect, with controls including position, size, and rotation point. It does not claim that Transform restores content already cropped by a preceding effect. Check the Transform manual.
Record a visible-pixel acceptance check
The following is an author-recommended comparison worksheet, not a promised Kdenlive result. Use the same project frame, monitor scale, and review moments for each chain. “Visible” means the wanted source edge can be seen in the project monitor, not merely that the image has moved.
| Hypothetical chain and observation | Decision to record |
|---|---|
| Corners → 3-way Rotate → Transform; after rotation, the top source edge is absent, and Transform moves the remaining image down | Mark the top edge as lost at 3-way Rotate; note whether the move reveals it (the manual says rotated-out pixels are not shown by this later Transform) |
| Corners → Transform → 3-way Rotate; the needed top edge remains visible before rotation | Compare that same edge at peak rotation; keep this ordering only if the final frame retains the required edge without unwanted framing |
| 3-way Rotate → Corners → Transform; a side edge changes visibility after Corners | Record the first observed change and review this ordering on the same frames; the manuals do not specify the combined Corners behavior |
| Any ordering; left and right pass at the start but the bottom edge disappears on the final keyframe | Reject the sequence for that shot or revise the animation, then repeat the four-edge check |
A changed preview is evidence about that clip and effect chain, not a general rule that one Corners ordering is correct for every project.
Limits and the next step
If an edge vanishes after 3-way Rotate, moving the cropped result with Transform cannot restore that missing edge. Return to the chain and test whether the required placement can be achieved before the crop-producing step, or adjust the rotation and framing so the needed source area remains within the project frame. Recheck keyframes, since the frame with the greatest rotation may not be the frame that first loses a particular edge.
Do not assume increasing Scale will recover missing source pixels: the manual says Scale affects the monitor’s X and Y axes irrespective of rotation, but does not describe it as undoing a crop. The supplied pages also do not establish how Corners behaves when placed before or after 3-way Rotate. When the two arrangements differ, decide from the timeline comparison, not from an assumed mathematical equivalence. If no tested arrangement retains the wanted edges, revise the effect values or accept a tighter crop; do not describe absent detail as recoverable.
Common questions
Does Transform after 3-way Rotate help reposition the image? Yes, it can transform the clip that reaches it. It cannot show pixels already cropped by the preceding 3-way Rotate.
Is Corners always better before rotation? The supplied documentation does not establish that. Compare the actual effect orders on the frames that matter.
Which frames should I inspect? Check the largest rotation, the closest approach to each boundary, and the first and last frames, looking at all four edges.
Sources and next step
- 3-way Rotate — Kdenlive 26.08 Manual 26.08 documentation
- Transform — Kdenlive 26.08 Manual 26.08 documentation
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.