Treat the inset as two decisions: where its rectangle sits and how large it is in the project image; then, separately, whether the visible part of the source shows the right area. Kdenlive’s Transform effect can be controlled on the monitor and includes X/Y/W/H controls, but its manual does not describe those fields as an independent source-crop box. Set the inset geometry first, and do not turn on Distort just to make a subject fit.
Set the rectangle, then check the source framing
- Sketch the target on the project frame. Note the intended corner, approximate width and height, and any captions or other information that must remain readable underneath. This is a layout target, not a claim about Transform’s field units.
- Select the inset clip and add or open Transform. Use the monitor controls to place and size it by eye. For values you want to record or refine, use X/Y/W/H; the Kdenlive Transform manual identifies these as transformation controls but does not specify their units here. Check the result on the monitor rather than assuming a value represents a particular pixel coordinate.
- Inspect the subject after the rectangle is close. Check the edges that matter: for a person, head and chin; for a product, its silhouette or label. If a crucial edge is missing, decide whether the source itself needs reframing. Use a separate crop/reframe step only if your project provides one, then check the inset geometry again.
- Check the composite and proportions. Confirm the intended underlying image and any must-keep text remain visible. Leave Distort off unless non-uniform stretching is an explicit visual requirement; the manual says that enabling it permits non-uniform stretching. Check the composition result in the monitor rather than changing blend options to compensate for a framing problem.
Use a layout-and-framing worksheet
The figures below are a hypothetical planning sketch, not measured Kdenlive fields or a software test. For a 1920 × 1080 project, a creator might reserve an inset about 560 × 315 units on the page sketch, near the upper-right corner, while leaving a lower caption area clear. These notes describe the intended layout, not a Transform readout. As a proposed review method, capture the same monitor frame before and after adjustment at the same viewing scale.
| Check | Hypothetical observation | Decision |
|---|---|---|
| Rectangle boundary | Sketch places the inset near the upper right with visible space from the project edge | Compare the monitor result with the sketch; adjust position or size if it crowds the edge |
| Subject edges | A speaker’s hair and chin are both visible, but close to the inset boundary | Keep the crop only if both remain clear in the final viewing size; otherwise reframe the source or revise the target |
| Covered information and composite | A lower-third caption or important label is hidden beneath part of the inset, even though the underlying shot remains visible elsewhere | Move or resize the inset, or revise the composition, if that information must remain visible; record the overlap as a layout issue rather than a source-crop issue |
| Proportions | The subject looks unnaturally wide in the after view | Keep Distort off unless that stretch is intentional; revisit the framing instead |
Limits and what to do when it fails
Transform combines transformation and compositing, but the cited page does not define a separate source-crop control or a crop-and-transform effect order. If moving or resizing the clip to reveal the subject also ruins the desired inset rectangle, stop treating those as one adjustment. Use a distinct crop/reframe operation if available in your setup, verify its result on the monitor, or revise the inset layout. If the source does not contain the missing edge, a transform cannot restore recorded picture outside the source; choose a different source moment or accept a tighter composition.
If the lower image behaves unexpectedly, inspect the composition selection: the manual lists Alpha blend as the default and describes other available operations. That setting changes how clips combine; it does not replace checking whether the inset covers required information. See the Transform documentation for the available options.
Three quick questions
Are X/Y/W/H values project-monitor pixels?
Do not assume so from this page. Record the values Kdenlive displays and verify the rectangle visually; the cited manual does not state their units.
Why did the lower clip change when I adjusted composition?
Check which composition operation is selected and compare the monitor result. A different operation can change how the clips combine; it does not correct a misplaced inset.
Can Transform recover a cut-off face or product edge?
It cannot recreate picture that is absent from the source. Try a source moment with more headroom, or revise the inset framing and layout.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.