To place a clip on a screen filmed at an angle, use Kdenlive’s Corners effect to map the source through four corner positions. Match the screen’s visible top-left, top-right, bottom-right and bottom-left to the controls with those names, in that order. Then inspect the transformed edges against the project frame and decide how exposed background should be treated. The manual describes this as perspective distortion on a virtual canvas; it is not a lens-distortion correction.
Match the four corners and inspect coverage
- Apply Corners to the clip you want to place on the filmed screen. In the Project Monitor, switch on Edit Mode to use the corner handles; the manual says this mode is required for handle editing. Start by moving each handle toward its corresponding visible screen corner.
- Check the mapping in the documented order: Top-left, Top-right, Bottom-right, Bottom-left. If the quadrilateral twists or one edge runs to the wrong screen corner, correct the correspondence before fine adjustment. This ordering is the manual’s numbering scheme, not a claim that the corners must be adjusted in that sequence.
- Inspect all four edges at the monitor’s current view. The manual’s model places the clip frame on a larger virtual canvas and allows corners to move inside or outside the frame. Therefore, do not assume a handle outside the original frame is automatically an error; check whether the transformed image covers the intended screen and whether the project frame shows unwanted exposed areas.
- When handle placement is close, review the Top-left X/Y, Top-right X/Y, Bottom-right X/Y and Bottom-left X/Y values. The manual lists these coordinate controls with a range of 0–3000. Treat them as coordinates on the effect’s virtual canvas, not as project-pixel measurements. Adjust them only when the monitor view reveals a specific mismatch.
- Decide whether Enable Stretch is needed. The manual specifies that this switch must be on for Stretch X/Y to have an effect. Stretch moves the source along an axis by shifting the virtual frame center; it is separate from placing the four corners. Do not change it just to fix a corner correspondence error.
- If the transform exposes background, check Transparent Background. Feather Alpha controls the feather width at the border between the frame and exposed background, and works only when Transparent Background is enabled. Judge the result over the actual project background: feathering changes that border treatment, not the corner mapping.
Acceptance worksheet: hypothetical screen insert
The observations below are an author-proposed check, not a reported Kdenlive test or a promised effect result. Assume a 1920×1080 project and a filmed display whose visible corners, judged in the monitor, are A (upper-left), B (upper-right), C (lower-right) and D (lower-left). Record the correspondence and outcome rather than inferring a coordinate conversion from the project dimensions.
| Check | Hypothetical observation | Decision |
|---|---|---|
| Top-left and top-right | Their handles meet A and B, but the top edge misses the filmed bezel near B | Refine the top-right placement; do not compensate with Stretch first |
| Bottom-right and bottom-left | Both meet C and D; the insert’s lower edge still falls short of the visible screen | Inspect the entire edge and project frame before changing other controls |
| Frame coverage | A narrow strip of project background appears beside one transformed edge | Decide whether the screen should fill that area; record the exposure rather than assuming it is a transparent defect |
| Background treatment | Transparent Background is on; Feather Alpha is set above zero | Compare the boundary over the project background; feathering is available only with transparency enabled |
| Stretch check | Stretch X/Y has a value, but Enable Stretch is off | The manual says Stretch X/Y has no effect in this state; enable the switch only if axis stretching is intended |
Limits and what to try next
A four-corner fit concerns a plane’s perspective geometry. It does not establish that a curved, flexible or moving surface will align between its corners, and the cited manual does not describe tracking a screen through camera motion. If the corners align but the middle of an edge does not, first confirm that the photographed target is planar and inspect the source image; do not treat more Stretch as a documented repair for curvature. If a corner lies beyond the available virtual-canvas coordinate range, or the intended coverage cannot be reached, the documented controls may not meet the layout requirement. The manual does not specify a universal coordinate recipe or guarantee that a particular setting removes all exposed background.
Quick questions
Do the four screen corners have to be adjusted in order? No. Use the documented correspondence order to prevent swapping controls; the manual does not require a particular editing sequence.
Does Feather Alpha make the transformed image cover more area? The manual defines it as a border feather between the frame and exposed background. It does not describe it as a coverage or geometry control.
What does a corner value such as 2000 represent? It is a coordinate in the effect’s virtual canvas, whose described range is 0–3000. The manual does not equate that value with a project-pixel position.
Sources: Kdenlive Corners effect: description and parameters and Kdenlive Corners effect: virtual-canvas notes and corner order.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.