The correct choice depends on which side of the playhead is unwanted. Put the playhead exactly at the boundary between the portion to keep and the portion to remove: use ( to remove the clip and timeline space to the left of the playhead, or ) to remove the corresponding material to the right. Before either action, enable ripple and confirm the intended track is active. Kdenlive documents this as a ripple trim to the playhead, so the operation is not expected to leave a gap at that boundary. This guide applies to the active track’s result, not automatically to every aligned track.
Make the decision and perform the steps
Use a time range rather than the button label as your decision rule. If the approved section ends at 00:00:12:10 and the unwanted section begins there, place the playhead at 00:00:12:10. Material from 00:00:08:00 through 00:00:12:10 is the left side; material from 00:00:12:10 onward is the right side.
- Identify the AI-generated clip and write down the keep range, remove range, and exact playhead position. Move the timeline cursor by dragging, clicking, or using frame-step keys when needed; Kdenlive states that the timeline cursor and Project Monitor position stay synchronized.
- Select or activate the track containing the clip. Check the track header and its actual track state; Kdenlive says only active tracks can react to an edit function. Do not infer scope from a color alone, because color depends on the interface theme.
- Enable ripple. Place the playhead on the keep/remove boundary, then choose
(when the unwanted range is on the left, or)when it is on the right. - Inspect the active track at the boundary. Confirm that the intended range disappeared, the retained section begins or ends at the playhead as planned, and no gap remains there. Record the neighboring clip’s new position.
The official editing documentation describes the keyboard actions and their left/right results in Ripple Trim to Playhead. Its broader explanation of the Ripple Tool also distinguishes changing a clip’s duration from simply moving its source window.
A new acceptance worksheet
The following is an author-created worksheet using hypothetical observations. It is a comparison method, not a promise about an untested project.
| Case | Keep boundary | Intended removal | Active track | Hypothetical observation | Decision |
|---|---|---|---|---|---|
| A | 00:00:12:10 | 00:00:08:00–00:00:12:10, left side | V1 | Check whether the intended left-side material and space were removed, whether the retained side matches the plan, and whether the operation left a gap at the boundary. Record the following V1 clip’s actual position without presuming its direction of movement. | Decide from the observed range and boundary; record the neighboring clip position |
| B | 00:00:12:10 | 00:00:12:10–00:00:17:00, right side | V1 | Check whether the intended right-side material and space were removed, whether the retained side matches the plan, and whether the operation left a gap at the boundary. Record the neighboring V1 clip’s actual position without presuming its direction of movement. | Decide from the observed range and boundary; record the neighboring clip position |
| C | 00:00:12:10 | Left side intended, but V2 changes | V1 active, V2 observed | V1 matches the worksheet while V2 is unchanged or differently affected | Review other tracks separately |
| D | 00:00:12:10 | Either side | No confirmed active track | The wrong clip changes or the expected range remains | Do not approve; restore the intended track state and reassess |
Record the actual removed interval and the adjacent clip positions after the operation. The worksheet’s frame values are hypothetical; they do not establish a Kdenlive counting rule or guarantee that a particular media layout will produce those observations.
Limits and next steps after failure
If a gap remains, first determine whether ripple was enabled and whether the playhead was placed at the true boundary. Also verify that the intended track was active. If the operation affects the wrong clip, stop and check the track header, selection, and current cursor position before repeating it.
This command is not the same as shortening one clip with a regular resize, using the Razor Tool followed by deletion, or applying a ripple edit to several aligned tracks. Kdenlive separately documents ripple deletion on the active track and timeline-zone extraction across unlocked tracks. Do not treat a successful active-track trim as proof that audio or other video tracks stayed synchronized. For multi-track removal, define the desired range and use the operation whose documented scope matches that requirement.
Three quick questions
Which side should I remove? Remove the left side when everything before the playhead is unwanted. Remove the right side when everything after it is unwanted. The keep/remove boundary decides; the AI origin of the clip does not.
Does the operation trim every track? The documented Ripple Trim to Playhead instruction is framed around a clip on an active track. Check other tracks separately unless you deliberately use a documented multi-track operation.
What should I record for approval? Record the playhead time, keep range, removed side, active track, actual removed range, and the new positions of adjacent clips. That makes the result auditable without assuming that a no-gap appearance proves all tracks changed correctly.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.