Usually, change an effect across a group only when every clip that already has that effect should receive the new parameter value. If only effects with matching parameter values should change, enable that restriction; if the clips need different results, inspect and adjust them individually. In Kdenlive, these options govern effects on grouped clips, not every property of every clip.
Decide the scope before changing a parameter
Kdenlive groups keep clips together for operations such as moving them while retaining their relative positions. Effect changes have a separate scope. The Kdenlive grouping manual says that enabling “Apply effect change to all clips in the group” applies a parameter adjustment to group members that also have that effect. Deleting an effect while this option is enabled deletes it from all clips in the group. A separate option, “Apply only to effects with the same value,” restricts changes to effects whose parameter value matches.
Use this sequence for a grouped sequence of AI-generated shots:
- Select the group and inventory its clips. For each member, note whether the target effect exists and record the relevant current parameter value. Do not infer that a clip without the effect will receive it.
- Identify the intended outcome: one shared value for every matching effect, a change only to effects already at a particular value, or distinct settings for particular clips.
- Before editing, inspect the group-effect controls. If you want all clips with the target effect changed, enable the all-clips option. If only matching starting values should change, also use the same-value restriction. If some clips need different settings, edit those effects individually instead of applying a group-wide change.
- Read the orange number shown beside an effect name when the all-clips option is enabled. The manual describes it as an indication of how many effects in the group are found and will be affected. Treat it as a scope clue, then confirm the actual result on the clips.
- For deletion, pause and check the scope controls. The manual states that deleting an effect deletes it on all clips in the group; do not rely on Alt-click selection to isolate effect deletion. If only one member should lose the effect, first ungroup the clips using Timeline > Ungroup Clips (or the documented context-menu or Ctrl+Shift+G method), then delete that member’s effect and verify that the other clips retain theirs.
The manual documents Alt-click for selecting an individual grouped item and lists deleting, moving, and cutting as operations on that clip. However, it separately states that deleting an effect deletes it on all clips in the group. It does not establish that Alt-click overrides this effect-deletion behavior; ungroup first if deletion must be limited to one member.
Effect impact worksheet
The following values are a hypothetical planning example, not a Kdenlive test or a guaranteed result. Assume a group contains four shots and the target is an existing “Soft Glow” effect. Values represent one numeric parameter chosen for the worksheet; they do not describe a particular effect’s real scale or recommended setting.
| Group member | Effect present? | Current value | Proposed value | All-clips option: candidate for change | Same-value restriction: candidate if matching 0.40 |
|---|---|---|---|---|---|
| Shot A, close-up | Yes | 0.40 | 0.55 | Yes | Yes |
| Shot B, wide view | Yes | 0.40 | 0.55 | Yes | Yes |
| Shot C, detail | Yes | 0.25 | 0.55 | Yes | No |
| Shot D, cutaway | No | — | 0.55 | No existing effect to adjust | No existing effect to adjust |
In this example, the all-clips option could affect A, B, and C because each has the effect. With the same-value restriction set to 0.40, A and B are the candidates; C starts at 0.25, and D has no such effect. These are worksheet deductions from the documented rules, not a promise about an unobserved interface state. After a change, compare each member’s effect value with the worksheet and check that clips outside the intended scope remain unchanged. If the visible result does not fit the recorded scope, stop and inspect the selection and option states before making another adjustment.
Limits and what to do if the result differs
Grouping does not mean that all clip attributes synchronize. The documented effect behavior concerns a parameter change for an effect that is present on group members, with the same-value option narrowing which effects change. It does not establish that grouping synchronizes clip content, timing, AI-generated details, or unrelated properties. Nor does the manual specify how every parameter type is compared, so do not assume that visually similar values count as identical.
If an unintended clip changes, use the worksheet to identify which scope assumption was wrong. Recheck whether the all-clips option and same-value restriction were enabled, whether the intended member was selected, and whether the target effect existed on that member. For a clip that must differ, adjust its effect separately and verify the individual result. If deleting an effect removes it from several clips, treat that as documented group behavior. To delete it from just one member, ungroup first, then delete and verify the per-clip state.
Common questions
Does the all-clips option add the effect to clips that do not have it?
The manual describes changing effects on group members that have the effect. It does not say that this option adds the effect to members without it.
What does the orange number tell me?
It indicates how many effects in the group are found and will be affected when the all-clips option is enabled. Use it as a cue to review scope, not as a substitute for checking each clip.
Can I delete the effect from just one grouped clip?
The manual states that deleting an effect deletes it on all clips in the group; it does not document Alt-click as an exception to that rule. To limit deletion to one member, ungroup the clips first using Timeline > Ungroup Clips, the context menu, or Ctrl+Shift+G. Then delete that member’s effect and verify the other clips.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.