When an AI-assisted edit contains many cuts, use Kdenlive's Identify Gaps command to mark suspected spaces in bulk, then turn those markers into a review list. This is an inspection workflow: the command creates timeline range markers; it does not close gaps, move clips, or repair sync. Choose whether the audit covers all tracks or only the selected track, and keep a separate check for audio-only tracks because the documented gap detection ignores them.
Specific decisions and steps
Use this workflow when the question is “where are the video gaps?” rather than “how should this gap be removed?” First decide the audit scope. If gaps may exist across several video tracks, click an empty timeline area and choose Identify Gaps > All Tracks. If you are checking one track in isolation, select the relevant track and choose Identify Gaps > Selected Track. The right-click menu documents both choices: Kdenlive Right-Click Menus.
- Open the sequence and identify the video tracks that belong to the approved edit. Treat track labels and actual clip types as evidence; a color is only a clue.
- Apply the appropriate
Identify Gapsscope from empty timeline space: all tracks for a sequence-wide pass, or the selected track for a focused pass. - Review the resulting range markers on the timeline. Each marker is an item to investigate at its displayed position, not an instruction to delete or fill the space.
- For every marker, record the time position, the relevant video track, the clip before and after it, and a decision such as
confirmed gap,intentional pause, orfalse positive. - Repeat the review for audio-only tracks manually. Keep this as a separate audit column because the official documentation says those tracks are ignored.
If the command reports no gaps, record the scope used. “No gaps found” applies to that detection pass and does not establish that audio-only tracks are gap-free.
A new acceptance worksheet
The following is a hypothetical example of an audit record, not a claim about Kdenlive's internal counting or measurement algorithm. The timecodes and decisions are invented to show how to make the result reviewable.
| Marker position | Detection scope | Track and neighboring clips | Manual observation | Acceptance decision |
|---|---|---|---|---|
| 00:02:14:08–00:02:15:03 | All Tracks | V2, interview_A to interview_B | Picture disappears for 19 frames; dialogue continues on A1 | Confirm video gap; escalate for editorial decision |
| 00:07:40:00–00:07:41:12 | Selected Track | V3, title_overlay only | V1 remains covered; V3 is intentionally empty | Accept as intentional layer gap |
| 00:11:05:18–00:11:06:02 | All Tracks | V1, b-roll_04 to b-roll_05 | Marker aligns with an approved pause card | Accept; retain marker as review evidence |
| 00:14:22:00–00:14:24:10 | Not detected by command | A2, music_clip_03 to music_clip_04 | Audio-only space found during waveform review | Record separately; do not call the video audit complete |
A practical acceptance rule is: every generated marker has a documented track, neighboring clips, and human decision; every audio-only track has a separate status. Use the timeline marker documentation to edit marker comments or manage the marker list when the timeline becomes crowded.
Limits and the next step after failure
A range marker identifies a location for review. It does not prove that the space is an error, and it does not distinguish an intentional pause from missing media. Do not describe the result as automatic gap repair.
The main boundary is media type: the documented identification checks gaps between video clips and ignores audio-only tracks. If the video pass is clean but a mix still contains an unwanted pause, inspect the audio tracks independently. If the selected-track pass misses a gap visible elsewhere, rerun the command with All Tracks and record that scope change. If no marker appears where you expect one, verify that the space is between video clips, that the intended track was included, and that you are looking at timeline range markers rather than clip markers.
Three short questions
Does a marker mean I should remove the space?
No. It is an audit flag. Decide whether the gap is intentional before using any editing operation.
Should I always choose All Tracks?
Choose it for a sequence-wide video pass. Use Selected Track when isolating one track, then record the narrower scope so the result is not mistaken for a complete audit.
Can this confirm that the audio is continuous?
No. Audio-only tracks are outside the documented identification behavior. Add a separate audio review using your normal timeline or waveform inspection method.
Sources and next step
- Timeline Markers — Kdenlive 26.08 Manual 26.08 documentation
- Right-Click Menus — Kdenlive 26.08 Manual 26.08 documentation
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the film workspace. The external software controls discussed above belong to their respective products.