Choose a point, line, or curve according to the local structure you need to move, not according to a universal portrait-shaping rule. In darktable 5.6 Liquify, shapes use nodes, an effect radius, and strength vectors; these settings guide the distortion. Plan the contour in short sections and inspect the target and neighboring structures before extending the edit.
Plan the shape and inspect its reach
Use a point when a single node should control a local distortion; if you need a radial strength distribution, choose the corresponding point mode. Use a line when the path should be linked by straight segments, and a curve when it should be linked by curved segments. Both lines and curves consist of sequences of linked nodes, and a line or curve segment can be converted to the other type. Choose according to the path geometry needed, not as a rule for particular body parts.
Work through the image in this order:
- Identify the target contour and mark where it changes direction. Also note nearby features that should remain visually stable, such as a clothing edge or a straight background line.
- Choose the simplest shape that can follow the target path. For a curve, place a few nodes at meaningful bends and endpoints rather than at every small contour variation.
- Set each node’s radius to the area you intend to influence. The manual defines the radius as the extent within which distortion occurs; inspect whether that area reaches a neighboring contour or background feature.
- Set the strength vector deliberately. For a point, choose linear, radial growing, or radial shrinking as appropriate, and check the arrow’s direction and length. In linear mode, distortion starts on the side opposite the vector and follows its direction. In radial growing mode, strength starts at 0% in the center and increases outward; in radial shrinking mode, it starts at 100% in the center and decreases outward. These radial modes describe strength distribution, not distortion direction. By default, strength varies linearly from 0% to 100% between the center and the radius; clicking the circle’s center lets you modify the feathering. Feathered mode provides two independently adjustable control circles.
- Review curve connections before adding nodes. Autosmooth computes handles automatically; cusp permits independent handles; smooth keeps a smooth curve; symmetrical moves the handles together. Use the mode that fits the turn or junction, then reassess the path.
- Toggle node editing to inspect the distortion objects and their controls. Read the displayed warp and node counts, and keep each module instance within the documented 100-node maximum.
The darktable 5.6 Liquify manual describes how node radius and strength vectors define the affected area and distortion direction. It also explains that point modes change how strength is distributed, so a point’s arrow alone does not tell the whole story.
Hypothetical contour review worksheet
Hypothetical planning worksheet, not an executed edit or guaranteed result: imagine a curved jacket edge beside a narrow, straight railing. The target is a small inward adjustment at one bend; the railing should remain visually straight. Node counts are illustrative planning counts, not quality scores.
| Segment and planned shape | Hypothetical setup | Observation to check | Decision if it fails |
|---|---|---|---|
| Gentle main bend: curve | 3 nodes; radius set to cover the bend; adjust the vector incrementally toward the intended displacement while checking the neighboring structure; smooth connection at the bend | Does the jacket edge move while the railing stays straight? | Reduce the radius or reconsider the vector before adding a node. |
| Short transition: point | 1 node; linear mode; arrow aligned with the desired local direction; radius set for the intended influence area | Does the distortion stay within the intended influence area, considering the selected point mode, vector direction, and radius? | Recheck the mode, vector direction, radius, and feathering. |
| Tight junction: curve | 2 nodes; cusp at the sharp turn; handles adjusted independently | Does the turn remain controlled without a kink spreading along the path? | Adjust the connection and handles; add a node only if the path still cannot describe the turn. |
As an author-recommended comparison, inspect the target contour, the nearby contour, and the background line at the same zoom level before deciding whether to keep a shape. The worksheet is hypothetical, not an official test or a claim that a specific radius or strength produces a particular displacement.
Limits and the next step when it fails
The manual limits each Liquify instance to 100 nodes and notes that the module consumes substantial system resources. Before extending an edit, check the displayed warp and node counts. If the plan approaches the limit, simplify paths where possible or consider an additional instance, accounting for the resource cost.
If the nearby structure bends unexpectedly, revisit the radius and strength direction, then the curve’s connection mode and handles. If needed, split the edit into simpler local shapes and inspect their combined result. Liquify is a creative distortion tool, not a method for recovering absent detail or correcting whole-image perspective.
Common questions
Should every contour use a curve?
No. Choose the shape that represents the intended local movement. A curve is useful when curved interpolation is needed, but it is not automatically better for every contour.
Does a larger radius make the edit safer?
Not necessarily. The radius describes the region in which distortion occurs. A larger region may reach features you meant to protect, so judge it against both the target and nearby structures.
When should I convert a line segment to a curve?
Use Ctrl+Alt-click on a segment to switch it between line and curve when the needed path geometry changes. This can avoid adding a control point solely to approximate a curved segment.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.