If the subject’s mid-tones look too dark, adjust the scene-referred Exposure module first. Set the subject to the intended brightness, then evaluate filmic RGB’s white and black relative exposure. Reveal and use filmic’s custom middle-gray luminance only when you have a specific reason to redefine which scene luminance represents display middle gray. The two controls are not interchangeable brightness sliders: Exposure changes the scene signal before filmic, while custom middle gray changes filmic’s reference and automatically moves its white and black exposure settings.
Judgment and steps
- Choose a representative subject area, such as a face, a product surface, or a gray card. Avoid using a specular highlight or a deep crease as the definition of the subject’s mid-tone. The Exposure picker can set exposure from the average of a selected region; its area-mapping feature can also match a chosen lightness target, but that workflow is distinct from filmic’s scene-range pickers. See the official Exposure documentation.
- In
Exposure, raise or lowerexposureuntil that representative area has the intended brightness. This is the normal documented route for setting mid-tones in a filmic workflow. Keep an eye on black areas: the filmic documentation warns that negative pixels can make later calculations unpredictable.
- With the subject brightness established, inspect filmic RGB’s
white relative exposureandblack relative exposure. These define how far above and below scene middle gray the display white and black bounds are placed. Adjust them only when the scene’s usable range or the desired highlight and shadow retention requires it. The filmic RGB manual describes these as scene-range controls, not as a replacement for Exposure.
- Use
use custom middle-gray valuesonly for a deliberate reference choice, such as a measured gray patch or a carefully selected subject region. After changingmiddle-gray luminance, recheck both relative-exposure values. The control automatically adjusts white and black exposure to avoid immediate range problems, but you can correct those values afterward.
- Compare the result at normal viewing size and watch the important bright and dark regions. Near 100%, middle-gray luminance does not compress highlights, but it fails to recover shadows. Near 0%, it recovers shadows more strongly, but compresses highlights more harshly and can reduce local contrast. Treat these as trade-offs, not as a free brightness gain.
A new acceptance worksheet
Use this as a controlled comparison. The numbers below are hypothetical observations, not guaranteed darktable outputs or a prescribed sampling algorithm.
| Subject sample | Exposure before/after | Filmic white/black relative exposure | Custom middle gray observation | Decision |
|---|---|---|---|---|
| Face, average region | -0.7 EV / -0.1 EV | +3.8 EV / -8.5 EV | At 72% (near the high end): highlights are less compressed, but shadows are not recovered | Keep Exposure correction; no custom middle gray |
| Gray card, known neutral patch | -0.7 EV / -0.1 EV | +3.8 EV / -8.5 EV | At 48%: range shifts; inspect whether the card remains the intended reference and check both ends | Use only if the card is the intended scene reference |
| Bright product surface | -0.7 EV / -0.1 EV | +3.8 EV / -8.5 EV | At 24% (near the low end): shadows recover more, but highlights are more compressed and local contrast may fall | Reject for this subject; retain Exposure and tune range |
The useful question is not which slider makes the preview lighter. It is whether the chosen reference remains credible while the white and black bounds still serve the image.
Limits and next steps
Filmic compresses dynamic range and can reduce local contrast; its documentation suggests considering local contrast afterward, but that is a separate creative correction. Highlight reconstruction is not a general method for recovering large clipped areas or missing detail. If the Exposure correction makes the subject acceptable but the image still has clipped highlights, inspect the raw clipping state and filmic’s range before attempting reconstruction.
If a gray-card sample and a subject sample demand incompatible middle-gray placements, do not average them blindly. Decide which one is the scene reference, or keep Exposure as the brightness correction and use filmic’s white/black controls for range management. If the picker gives an implausible black reading, especially near -16 EV, the manual warns that the measurement may have failed; adjust it manually and judge the actual image.
Three quick questions
Should I show the hidden slider whenever the face is dark? No. It is hidden by default because the manual recommends Exposure for setting middle gray. Reveal it only for a defined custom reference.
Does lowering middle gray simply brighten the image? No. It changes the reference and automatically shifts white and black relative exposure. Near the low end it may recover shadows while compressing highlights and reducing local contrast.
Can filmic’s white picker set the subject brightness? Not directly. It assumes the sampled maximum is scene white and sets the white bound. That is a range decision, not a subject middle-tone target.
Sources and next step
This guide interprets public documentation and uses explicitly hypothetical acceptance examples, not application tests. Controls and availability can change; verify the cited manual against your installed version.
For work created in Imagild, carry the input requirements and acceptance checklist into the photo editor. The external software controls discussed above belong to their respective products.